input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 307 747k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "X05CG加圧力測定用ジグ(バックアップステージ(ガラス))P",
"WorkName": "本圧着加圧力測定治具組立",
"Words": [],
"WorkItems": [
"1. BLOCK にBRACKET をBOLT WASHER で取付ける",
"2. 1.完成品にPUSHER をSCREW で取付ける"
],
"WorkPoints": [
"止めﾈｼﾞが緩まない様に最後まで締付ける事",
"治具使用時にﾎﾞﾙﾄを緩めるため軽く締付ける"
],
"Tolks": [],
"InspectionI... | [
{
"WorkName": "本圧着加圧力測定治具組立",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowID": "... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "本組立前準備1_ﾍﾞｱﾘﾝｸﾞ組立",
"Words": [
"FM-2250(下側)",
"FM-2250(上側)",
"治具に①を挿入する",
"治具の上側を被せ②を挿入し圧入",
"ﾍﾞｱﾘﾝｸﾞよりﾋﾟﾝが飛び出してい無い事を確認"
],
"WorkItems": [
"1. ①に②を圧入"
],
"WorkPoints": [
"治具のﾋﾟﾝがある方にﾍﾞｱﾘﾝｸﾞをｾｯﾄする(4箇所)",
"ﾃｰ... | [
{
"WorkName": "本組立前準備1_ﾍﾞｱﾘﾝｸﾞ組立",
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞ､Dﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "本組立前準備2_ﾋﾟﾝ圧入",
"Words": [
"▲1. ①を②に圧入する",
"出代39mm",
"FM-2252①",
"FM-2252②",
"接着剤塗布 米粒:1"
],
"WorkItems": [
"▲1. ②に接着剤を塗布し①に圧入"
],
"WorkPoints": [
"圧入後､指で引っ張り抜け無い事を確認",
"ﾋﾟﾝのﾃｰﾊﾟ側(圧入部6㎜)に塗布する事",
"治具①に②... | [
{
"WorkName": "本組立前準備2_ﾋﾟﾝ圧入",
"QualityItem": "圧入確認",
"ToolManageNo": "FM-2252",
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "本組立前準備3_ﾌﾞﾛｯｸ組立",
"Words": [
"3㎜",
"3㎜",
"2個作成",
"FM-2253(下側)",
"FM-2253(上側)",
"治具(上側)を被せ②を入れ圧入"
],
"WorkItems": [
"1. ①に砥石を掛ける",
"2. 1完成品に②を圧入"
],
"WorkPoints": [
"加工面(表･裏両面)にかける事",
"ﾋﾟﾝ出代:3㎜(両端)... | [
{
"WorkName": "本組立前準備3_ﾌﾞﾛｯｸ組立",
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:両端3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"Flo... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立1_砥石掛け",
"Words": [
"表面",
"裏面",
"表面と裏面をかけること",
"ﾊﾞﾘ､打痕がないか確認する事",
"2.㉗で表裏を清掃する",
"使用治工具No.27"
],
"WorkItems": [
"1. ①に油砥石(ｱﾙﾐ用)をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"Inspe... | [
{
"WorkName": "ﾍﾞｰｽ組立1_砥石掛け",
"QualityItem": "ﾊﾞﾘ確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘがないか確認",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowID": "0"
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立2_ﾋﾟﾝ圧入",
"Words": [
"表面",
"1.5㎜"
],
"WorkItems": [
"1. ①に②を圧入"
],
"WorkPoints": [
"ﾋﾟﾝ出代:1.5㎜",
"座ｸﾞﾘ有りが表面",
"ﾃｰﾊﾟｰ側を圧入"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ﾍﾞｰｽ組立2_ﾋﾟﾝ圧入",
"QualityItem": "ﾋﾟﾝ出代",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:1.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowI... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立3_ﾍﾞｱﾘﾝｸﾞ取付",
"Words": [],
"WorkItems": [
"1. ①に②を通し③に圧入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
"Too... | [
{
"WorkName": "ﾍﾞｰｽ組立3_ﾍﾞｱﾘﾝｸﾞ取付",
"QualityItem": "圧入確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り圧入出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowID... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立4_ﾎﾙﾀﾞ取付",
"Words": [],
"WorkItems": [
"1. ①に②を③で取付"
],
"WorkPoints": [
"ﾍﾞｰｽのDﾋﾟﾝに挿入した後､ﾎﾞﾙﾄを締結"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels... | [
{
"WorkName": "ﾍﾞｰｽ組立4_ﾎﾙﾀﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立5_ｼｬｯﾀｰﾍﾞｱﾘﾝｸﾞ取付",
"Words": [],
"WorkItems": [
"1. ④に②③を通し①に取付",
"2. ④に⑤を通し①に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
... | [
{
"WorkName": "ﾍﾞｰｽ組立5_ｼｬｯﾀｰﾍﾞｱﾘﾝｸﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNam... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立6_ｽﾄｯﾊﾟｰｶﾗｰ取付",
"Words": [],
"WorkItems": [
"1. ④に②③を通し①に取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo"... | [
{
"WorkName": "ﾍﾞｰｽ組立6_ｽﾄｯﾊﾟｰｶﾗｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾍﾞｰｽ組立7_ﾌﾞﾛｯｸ取付",
"Words": [],
"WorkItems": [
"1. ①に②を③で取付"
],
"WorkPoints": [
"ﾃｰﾊﾟ側を下側にして挿入"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾍﾞｰｽ組立7_ﾌﾞﾛｯｸ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ﾌﾞﾛｯｸ取付②",
"Words": [],
"WorkItems": [
"1. ①に②を③で取付",
"2. ①に④を③で取付"
],
"WorkPoints": [
"②④を図の方向でDﾋﾟﾝに挿入し③で締結"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"W... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｼｬｯﾀｰ組立",
"Words": [],
"WorkItems": [
"1. SHUTTER にBLOCK COLLAR GUIDE をBOLT で取付",
"2. 1完成品にCOLLAR GUIDE をBOLT で仮取付"
],
"WorkPoints": [
"仮取付で組立(穴位置は図の通り)",
"仮組立品を㉘治具に取付",
"GUIDE を治具のDﾋﾟﾝに当てつけ",
"全体を矢印方向に押し治具に当てﾚﾊﾞｰで固定する"... | [
{
"WorkName": "ｼｬｯﾀｰ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｼｬｯﾀｰ取付①",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"2. ①に②を挿入し､③④で取付",
"◆1. ①のﾍﾞｱﾘﾝｸﾞ(8か所)にｸﾞﾘｰｽを塗布",
"3. ベアリングとガイドの当たりを調整し隙間が無いことを㉙にて4箇所確認すること"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞとｶﾞｲﾄﾞの当たり調整ｼｬｯﾀｰ動作時に各ﾍﾞｱﾘﾝｸﾞが回転する事",
"... | [
{
"WorkName": "ｼｬｯﾀｰ取付①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｽﾄｯﾊﾟｰﾌﾞﾛｯｸ取付",
"Words": [
"接着剤塗布 米粒:2",
"接着剤塗布 米粒:1"
],
"WorkItems": [
"▲1. ②に③を接着",
"▲2. 1完成品を④⑤で①に取付"
],
"WorkPoints": [
"ﾃｰﾊﾟｰ側を挿入",
"③を挿入する前に接着剤を塗布",
"④のﾎﾞﾙﾄ先端に接着剤を塗布",
"ｼｬｯﾀｰを矢印方向に押し､治具に当てつけ0.02㎜ｼｯｸﾈｽ... | [
{
"WorkName": "ｽﾄｯﾊﾟｰﾌﾞﾛｯｸ取付",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "剥がれ無き事米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "接着剤ｽｰﾊﾟｰX",
"ProcessNames": [
"特殊工程"
],
"Fl... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｼｬｯﾀｰ取付②",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1",
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1. ⑤とWASHER にｸﾞﾘｰｽを塗布",
"2. ①に⑤をBOLT で取付し､SPRING を挿入",
"3. GUIDE にWASHER を貼付し､BOLT WASHER で取付"
],
"WorkPoints": [
"PINがGUIDE穴の中心になるよう調整",
... | [
{
"WorkName": "ｼｬｯﾀｰ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｶﾞｲﾄﾞ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 小豆:1",
"FM-2178"
],
"WorkItems": [
"1. ①にGUIDE をBOLT WASHER で取付",
"◆2. 1完成品にｸﾞﾘｰｽを塗布"
],
"WorkPoints": [
"治具にて調整し本締めの為､仮締め",
"ﾁｪﾝｼﾞｬｰを治具にｾｯﾄ",
"GUIDE を治具に当てつけ(矢印方向)て取付",
"締結後､ｼ... | [
{
"WorkName": "ｶﾞｲﾄﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2178",
"ToolName": "ｶﾞｲﾄﾞ位置調整治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "ｼｬｯﾀｰ動作確認",
"Words": [],
"WorkItems": [
"1. ｼｬｯﾀｰの動作確認実施"
],
"WorkPoints": [
"ｼｬｯﾀｰをﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞで押して開くときのｽﾄﾛｰｸ全域での最大荷重を測定⇒ 4N以下"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ｼｬｯﾀｰ動作確認"
],
"InspectionNos": [
"DH7M-D0... | [
{
"WorkName": "ｼｬｯﾀｰ動作確認",
"QualityItem": "摺動確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"ToolCycle": "1回/年",
"ToolRecord": "校正成績書",
"StdVal": "ｽﾄﾛｰｸ全域にて4N以下",
"Method": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"RecordMethod": "DH7M-D019-024",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "銘板貼付",
"Words": [
"40㎜",
"1㎜",
"1㎜",
"28㎜",
"25㎜",
"1.5㎜",
"当付け方向",
"当付け方向"
],
"WorkItems": [
"1. ①に㉗でLABEL LABEL を貼付",
"2. 1完成品に④を貼付"
],
"WorkPoints": [
"㉗のピン（３ヶ所）を シャッター側面にスキマ無く 当付けること",
... | [
{
"WorkName": "銘板貼付",
"QualityItem": "貼付確認",
"ToolManageNo": "FM-6326",
"ToolName": "ﾗﾍﾞﾙ位置決めｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
... | information_extraction | 0 | null | |
{
"UnitName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ部(12ﾉｽﾞﾙ)★D",
"WorkName": "機能検査",
"Words": [],
"WorkItems": [
"2. ﾉｽﾞﾙｾｯﾄ確認",
"1. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ脱着確認"
],
"WorkPoints": [
"ｽﾑｰｽﾞにｾｯﾄできる事",
"ｼｬｯﾀｰを閉じて抜け無い事",
"着脱の際､引っかかりなく着脱できる事",
"ﾁｪﾝｼﾞｬｰを治具の上にｾｯﾄ(ﾚﾊﾞｰを押さない状態)",
"治具のﾚﾊﾞｰを押すと自重にて落下する事",
"治具と... | [
{
"WorkName": "機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り動作する事",
"Method": "目視",
"RecordMethod": "DH7M-D019-024",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "枠組立て1/3",
"Words": [
"面取り部が外向き",
"取付け方向に注意! この部品には方向性があります｡"
],
"WorkItems": [
"1. GUIDE GUIDE にGREASE-NIPPLE を取付",
"2. 1完成品にPLATE をBOLT で仮取付"
],
"WorkPoints": [
"GUIDE GUIDE のｼﾘｱﾙが一致しているか確認してから､脱脂､砥石がけ",
"PLATE に脱脂､砥石がけSD-01214... | [
{
"WorkName": "枠組立て1/3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.4N・m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "枠組立て2/3",
"Words": [
"B",
"A"
],
"WorkItems": [
"1. ①に㉘を乗せてⒶⒷを㉘に押当て(挟み込み） M8×25で締結"
],
"WorkPoints": [
"㉘ⒶⒷのスキマ（紫線の箇所）に、0.01㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"締結後､治具が矢印方向に動く事",
"M8×25",
"規格値:ｼｯｸﾈｽｹﾞｰｼﾞが入らないこと",
"しっかりと押し当てないと､ｽｷﾏが発生... | [
{
"WorkName": "枠組立て2/3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "枠組立て3/3",
"Words": [],
"WorkItems": [
"2. 1完成品に㉙乗せてBOLT で締結",
"1. ①にPLATE をBOLT で仮取付",
"◆3. 2完成品にCUTTER を乗せｽﾑｰｽﾞに摺動するか確認",
"◆4. 確認後CUTTER を取外す"
],
"WorkPoints": [
"PLATE に､脱脂､砥石がけ",
"締結後､治具が矢印方向に動き\"紫線\" の箇所に､0.01㎜のｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事... | [
{
"WorkName": "枠組立て3/3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "26.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ｼﾘﾝﾀﾞｰ組立て",
"Words": [
"20mm",
"7mm",
"7mm"
],
"WorkItems": [
"1. CYLINDER にSPEED-CONTROLLER JOINT を取付",
"◆2. 1完成品にROD-END orROD-END をNUT で仮取付(仮位置出し)"
],
"WorkPoints": [
"ROD-END ﾛｯﾄﾞｴﾝﾄﾞにｸﾞﾘｰｽ(LCG100)塗布",
"ねじ込み後絶対に戻さないで下さい... | [
{
"WorkName": "ｼﾘﾝﾀﾞｰ組立て",
"QualityItem": "ｼﾞｮｲﾝﾄ出代",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ﾈｼﾞ部:7㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowID... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ｼﾘﾝﾀﾞｰ取付",
"Words": [
"4箇所"
],
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 20.5N･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治... | [
{
"WorkName": "ｼﾘﾝﾀﾞｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "20.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "可動刃取付",
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"稼動刃をｽﾗｲﾄﾞさせ､ｸﾞﾘｰｽを馴染ませる余分なｸﾞﾘｰｽ取り除く"
],
"WorkItems": [
"2. ②ガイド部に㉖を塗布(可動刃が摺動するところ）",
"◆1. ①可動刃のグリース用溝に㉖を塗布（表面・裏面・側面の6箇所）",
"◆3. 2完成品に①可動刃を乗せて摺動確認"
],
"WorkPoints": [
"側面",
"表... | [
{
"WorkName": "可動刃取付",
"QualityItem": "ｸﾞﾘｰｽ塗布",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:48",
"Method": "目視",
"RecordMethod": "ｰ",
"Others": "ｸﾞﾘ-ｽLCG100",
"ProcessNames": [
"-"
],
"FlowI... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ﾌﾟﾚｰﾄ取付",
"Words": [
"取付け方向に注意! この部品には方向性があります｡",
"狭い",
"狭い",
"短い",
"短い",
"ｼﾘﾝﾀﾞｰ側",
"⓶に、脱脂、砥石がけ 端面をGUID(P002,P003)に合わせ締結 取付方向注意"
],
"WorkItems": [
"◆1. ①にPLATE をBOLT で取付て､可動刃の摺動確認",
"◆2.1完成品にBOLT を取付て､可動刃の摺... | [
{
"WorkName": "ﾌﾟﾚｰﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "可動刃ｽﾄﾛｰｸ調整",
"Words": [
"5.8mm"
],
"WorkItems": [
"3. 調整後、シリンダーは、戻り限の状態でエアーを供給を止め㉖を取外す",
"◆2. ①可動刃のｽﾄﾛｰｸ調整",
"◆1. ①に、㉖を取付確認（1～5）及び、使い方"
],
"WorkPoints": [
"5.8㎜に対してﾌﾞﾛｯｸｹﾞｰｼﾞ5.6㎜が通り6.0㎜が止まる",
"可動刃の刃先には触れ無い事!!",
"白",
"黒... | [
{
"WorkName": "可動刃ｽﾄﾛｰｸ調整",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6438",
"ToolName": "ｴｱｰ供給治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "ｰ",
"Others": "-",
"ProcessNames": [
"-"
],
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ｶﾞｲﾄﾞ取付",
"Words": [
"取付け方向に注意! この部品には方向性があります"
],
"WorkItems": [
"◆1. ①にGUIDE をBOLT で取付"
],
"WorkPoints": [
"GUIDE を脱脂､砥石がけ",
"取付方向有り切り欠け部を可動刃の最大幅方向にて取付",
"可動刃の刃先には触れ無い事!!",
"GUIDE を上方向で仮取付 SD-0121411-109で本締結",
"刃先をｷｽﾞ付けない... | [
{
"WorkName": "ｶﾞｲﾄﾞ取付",
"QualityItem": "取付方向",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "切り欠き部分が可動刃の最大幅方向にて取付",
"Method": "目視",
"RecordMethod": "ｰ",
"Others": "-",
"ProcessNames": [
"-"
],
"FlowID":... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "固定刃取付位置合わせ",
"Words": [
"固定刃",
"ｽｷﾏ",
"可動刃",
"固定刃を取付しているﾌﾞﾗｹｯﾄを上下させ隙間を調整する｡ｼｯｸﾈｽｹﾞｰｼﾞ0.01mmが通り0.03mmが止まる事｡",
"固定刃",
"可動刃",
"固定刃",
"可動刃"
],
"WorkItems": [
"◆2. 固定刃と可動刃の隙間調整し､M8ﾎﾞﾙﾄ6ｶ所を締結",
"◆1. ①の可動刃を行き限に動かしCUTTER を... | [
{
"WorkName": "固定刃取付位置合わせ",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "11.5N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "開口部隙間調整",
"Words": [
"固定刃",
"可動刃",
"A"
],
"WorkItems": [
"2. 調整後、シリンダーは、戻り限の状態でエアー供給を止め㉘を取外す",
"◆1. ①に、㉘にて可動刃を戻り限にし、①の開口部寸法を調整し測定"
],
"WorkPoints": [
"可動刃･固定刃の刃先に注意すること!!",
"㉗ﾉｷﾞｽは、200㎜・300㎜でも使用可とする。",
"測定時､可動刃が戻り限であり､... | [
{
"WorkName": "開口部隙間調整",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6438",
"ToolName": "ｴｱｰ供給治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "ｰ",
"Others": "-",
"ProcessNames": [
"-"
],
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ﾊﾞｰ取付・ｶｯﾄと脱磁の確認",
"Words": [
"固定刃",
"可動刃",
"ｼｭｰﾄｶﾞｲﾄﾞﾊﾞｰ",
"ｽｷﾏB",
"切断箇所",
"幅20 mmのｺﾋﾟｰ用紙(PPC用紙,厚さ0.1mm以下)が切断箇所にて切断可能なことを確認",
"可動刃と固定刃に残留磁気が無いことをﾃｽﾗﾒｰﾀｰで確認 (ｶｯﾀｰの刃､全長にわたり測定)",
"FM-3098"
],
"WorkItems": [
"◆1. ①にBLOCK をB... | [
{
"WorkName": "ﾊﾞｰ取付・ｶｯﾄと脱磁の確認",
"QualityItem": "取付確認",
"ToolManageNo": "FM-6438",
"ToolName": "ｴｱｰ供給治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "ｰ",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "ｶﾊﾞｰ取付・給脂",
"Words": [
"ｼﾘﾝﾀﾞｰ側に押し当てて取付"
],
"WorkItems": [
"◆2. 1完成品にｸﾞﾘｰｽを注入",
"◆1. ①にCOVER をBOLT WASHER で取付",
"◆3. 2完成品の可動刃を固定刃まで(行き限)動かす"
],
"WorkPoints": [
"油溝の位置まで可動刃を出すこと",
"27㎜",
"注入後､余分なｸﾞﾘｰｽは拭取ること(左右)",
"左右のﾆｯ... | [
{
"WorkName": "ｶﾊﾞｰ取付・給脂",
"QualityItem": "取付位置",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｼﾘﾝﾀﾞｰ側に押し当て",
"Method": "目視",
"RecordMethod": "WCRE-E013-040",
"Others": "-",
"ProcessNames": [
"-"
],
"Fl... | information_extraction | 0 | null | |
{
"UnitName": "13連ｶｯﾃｨﾝｸﾞ",
"WorkName": "LABEL貼付け",
"Words": [
"20mm",
"20mm",
"45mm",
"25mm",
"45mm",
"25mm"
],
"WorkItems": [
"1. ①に②を貼付",
"2. 1完成品に③を貼付"
],
"WorkPoints": [
"脱脂し､貼付のこと",
"脱脂し､貼付のこと"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "LABEL貼付け",
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り貼付けて出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
],
"Flow... | information_extraction | 0 | null |
End of preview. Expand in Data Studio
No dataset card yet
- Downloads last month
- 4